Форум VolSat - Показать сообщение отдельно - Восстановление AMIKO SHD 8900 ALIEN / GI S8120 (SPARK)

CELLAR · 20.08.2012, 20:26

Доброго времени суток!Ув. знатоки подскажите!Принесли на ремонт рес. Amiko 8900 alien!!На табло горят ноли,через некоторое время загораются часы и мерцает экран ТВ,на кнопки пульта и дисплея не реагирует!Гипер терминал выдаёт сообщение такого плана
^X[MAIN] YWIDENT_Init error,errCode=0xff03
ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207)
[MAIN] init finish,errCode=0
Uя

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 bc 77
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867346 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970083 Bytes = 2.8 MiB
Image 1: 2897250 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00bc77
Loading Ramdisk to 80d3c000, length 002c3562 ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0

ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x
0053d000 - 2897250 ...

hя

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 bc 77
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867346 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970083 Bytes = 2.8 MiB
Image 1: 2897250 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00bc77
Loading Ramdisk to 80d3c000, length 002c3562 ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0

ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x
0053d000 - 2897250 ...

[MAIN] init finish,errCode=0
эїюю

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 bc 77
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867346 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970083 Bytes = 2.8 MiB
Image 1: 2897250 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00bc77
Loading Ramdisk to 80d3c000, length 002c3562 ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0

ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x
0053d000 - 2897250 ...

UХUл

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 bc 77
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867346 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970083 Bytes = 2.8 MiB
Image 1: 2897250 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00bc77
Loading Ramdisk to 80d3c000, length 002c3562 ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0

ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x
0053d000 - 2897250 ...

[MAIN] YWIDENT_Init error,errCode=0xff03
ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207)
[MAIN] init finish,errCode=0
Аю

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 bc 77
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867346 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970083 Bytes = 2.8 MiB
Image 1: 2897250 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00bc77
Loading Ramdisk to 80d3c000, length 002c3562 ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0

ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x
0053d000 - 2897250 ...

[MAIN] YWIDENT_Init error,errCode=0xff03
ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207)
[MAIN] init finish,errCode=0
что делать не знаю!!!!

20.08.2012, 20:26	#162
CELLAR Новичок Регистрация: 16.01.2010 Ресивер: OPENBOX F-300 Адрес: ДОНЕЦКАЯ ОБЛ. Сообщений: 4 Сказал(а) спасибо: 12 Поблагодарили 0 раз(а) в 0 сообщениях Вес репутации: 0	Доброго времени суток!Ув. знатоки подскажите!Принесли на ремонт рес. Amiko 8900 alien!!На табло горят ноли,через некоторое время загораются часы и мерцает экран ТВ,на кнопки пульта и дисплея не реагирует!Гипер терминал выдаёт сообщение такого плана ^X[MAIN] YWIDENT_Init error,errCode=0xff03 ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207) [MAIN] init finish,errCode=0 Uя Board: STx7111-Mboard (MB618) [32-bit mode] info: Disregarding any EPLD U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB * Warning - bad CRC, using default environment In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 bc 77 Hit ESC to stop autoboot: 0 ## Booting image at a0080000 ... Image Name: Kernel-Ramdisk-Image Image Type: SuperH Linux Multi-File Image (gzip compressed) Data Size: 5867346 Bytes = 5.6 MiB Load Address: 80800000 Entry Point: 80801000 Contents: Image 0: 2970083 Bytes = 2.8 MiB Image 1: 2897250 Bytes = 2.8 MiB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK found phy at addres = 1 stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1 stb_id = 90a00bc77 Loading Ramdisk to 80d3c000, length 002c3562 ... OK Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0ff stmm aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x 0053d000 - 2897250 ... hя Board: STx7111-Mboard (MB618) [32-bit mode] info: Disregarding any EPLD U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB * Warning - bad CRC, using default environment In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 bc 77 Hit ESC to stop autoboot: 0 ## Booting image at a0080000 ... Image Name: Kernel-Ramdisk-Image Image Type: SuperH Linux Multi-File Image (gzip compressed) Data Size: 5867346 Bytes = 5.6 MiB Load Address: 80800000 Entry Point: 80801000 Contents: Image 0: 2970083 Bytes = 2.8 MiB Image 1: 2897250 Bytes = 2.8 MiB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK found phy at addres = 1 stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1 stb_id = 90a00bc77 Loading Ramdisk to 80d3c000, length 002c3562 ... OK Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0ff stmm aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x 0053d000 - 2897250 ... [MAIN] init finish,errCode=0 эїюю Board: STx7111-Mboard (MB618) [32-bit mode] info: Disregarding any EPLD U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB * Warning - bad CRC, using default environment In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 bc 77 Hit ESC to stop autoboot: 0 ## Booting image at a0080000 ... Image Name: Kernel-Ramdisk-Image Image Type: SuperH Linux Multi-File Image (gzip compressed) Data Size: 5867346 Bytes = 5.6 MiB Load Address: 80800000 Entry Point: 80801000 Contents: Image 0: 2970083 Bytes = 2.8 MiB Image 1: 2897250 Bytes = 2.8 MiB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK found phy at addres = 1 stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1 stb_id = 90a00bc77 Loading Ramdisk to 80d3c000, length 002c3562 ... OK Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0ff stmm aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x 0053d000 - 2897250 ... UХUл Board: STx7111-Mboard (MB618) [32-bit mode] info: Disregarding any EPLD U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB * Warning - bad CRC, using default environment In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 bc 77 Hit ESC to stop autoboot: 0 ## Booting image at a0080000 ... Image Name: Kernel-Ramdisk-Image Image Type: SuperH Linux Multi-File Image (gzip compressed) Data Size: 5867346 Bytes = 5.6 MiB Load Address: 80800000 Entry Point: 80801000 Contents: Image 0: 2970083 Bytes = 2.8 MiB Image 1: 2897250 Bytes = 2.8 MiB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK found phy at addres = 1 stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1 stb_id = 90a00bc77 Loading Ramdisk to 80d3c000, length 002c3562 ... OK Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0ff stmm aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x 0053d000 - 2897250 ... [MAIN] YWIDENT_Init error,errCode=0xff03 ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207) [MAIN] init finish,errCode=0 Аю Board: STx7111-Mboard (MB618) [32-bit mode] info: Disregarding any EPLD U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 bc 77 Hit ESC to stop autoboot: 0 ## Booting image at a0080000 ... Image Name: Kernel-Ramdisk-Image Image Type: SuperH Linux Multi-File Image (gzip compressed) Data Size: 5867346 Bytes = 5.6 MiB Load Address: 80800000 Entry Point: 80801000 Contents: Image 0: 2970083 Bytes = 2.8 MiB Image 1: 2897250 Bytes = 2.8 MiB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK found phy at addres = 1 stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1 stb_id = 90a00bc77 Loading Ramdisk to 80d3c000, length 002c3562 ... OK Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0ff stmm aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa ddr:24:00:0A:00:BC:77 Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BC:77 - 0x 0053d000 - 2897250 ... [MAIN] YWIDENT_Init error,errCode=0xff03 ASSERT!! /home/d03ljf/workspace/spark_app_ret_duo_A34/src/main/main.c (3207) [MAIN] init finish,errCode=0 что делать не знаю!!!!