Подскажите что может быть нельзя перепрошить тюнер. Через гипертерменал пишет вот такое.
using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 ba 9f
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force rs232 upgrade u-boot, need 524288 Bytes(512kB)
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCCTimed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/1(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes
Transmit filesize is 0, please check your choiced file
пя
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 ba 9f
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867391 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970112 Bytes = 2.8 MiB
Image 1: 2897267 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90a00ba9f
Loading Ramdisk to 80d3c000, length 002c3573 ... OK
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/d
ev/ram0 ip=192.168.0.69:192.168.0.119:192.168.0.1:255.255. 255.0:lh:eth0
ff stmm
aceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwa
ddr:24:00:0A:00:BA:9F Manufacture=Spark-Project STB_ID=09:00:0A:00:00:BA:9F - 0x
0053d000 - 2897267 ...
[MAIN] init finish,errCode=0
[ YWDBASEv_GetData][ 578] error 0x1f40006
[ YWDBL_CommGetVolume][ 288] YWDBLi_CommGetByFldNoWithDefault COMM_VOLUME errTy
pe = 0X1F40006 Unknown
[ YWDBASEv_GetData][ 578] error 0x1f40006
[YWDBLi_ScGetByFieldNo][ 101] YWDBL_GetSysCfgField uFieldNo = 15[YWDBL_ScGetRes
olution][ 496] YWDBLi_ScGetByFieldNo SYSCFG_DEFINITE errType = 0X1F40006 Unknow
n
########################## uiCompSize[0X00AE8BCC]================
[*error*][YWFILE_IsDbFileOk:560]===Open file[./AppUserDb/syscfg.bin] failed===
[*error*][YWFILE_ReadFlashToDB:814]===Read [./AppUserDb/syscfg.bin] failed, take
[./AppUserDb/syscfgbak.bin] as default===
[*error*][YWFILE_IsDbFileOk:551]===File[./AppUserDb/syscfgbak.bin] CRC error===
[*error*][YWFILE_ReadFlashToDB:820]===Read [./AppUserDb/syscfgbak.bin] failed, t
ake [./AppUserDb/syscfgdef.bin] as default===
, using default environment
Да и на заводские настройки скидывать нехочет. Пишет ошибка.