Ребята, в общем мучаюсь 5-ый день, не знаю куда лучше писать, поэтому пишу сюда
приставка - SkyVision t2401
проц - gx3235s, проблема - включается и висит на заставке
флэш менял и перепрошивал два раза - не помогло и так далее, не суть, что еще делал в общем, сегодня подключился по UART
проц отвечает таким текстом:
error : configure DAC must set ENABLE_GX_OTP = y !
Partition Version : 102
Partition Count : 6
Write Protect : TRUE
CRC32 Enable : TRUE
Table CRC32 : FC076BA2
================================================== ============================================
ID NAME FS CRC32 START TOTAL_SIZE MAIN_SIZE USED_SIZE Use% RES_SIZE
================================================== ============================================
0 BOOT RAW 7CE23223 00000000 64 KB 64 KB 64636 B 98% 0 MB
1 TABLE RAW 00010000 512 B 512 B 512 B 100% 0 MB
2 LOGO RAW F6C8310C 00010200 65024 B 65024 B 58468 B 89% 0 MB
3 KERNEL RAW 8A2FE4FE 00020000 2560 KB 2560 KB 2541 KB 99% 0 MB
4 ROOT CRAMFS CFE1AEC1 002a0000 960 KB 960 KB 932 KB 97% 0 MB
5 DATA MINIFS FF000000 00390000 448 KB 448 KB 1 B 0% 0 MB
----------------------------------------------------------------------------------------------
GxLoader v1.9.6-x 20170220
cpu family : CSKY
chip model : gx6605s
board type : 6605s
memory size : 64 MB
Flash type : w25q32
Flash size : 4 MB
warning: board-init not call function enable_dac, will open cvbs & ypbpr default.
show jpeg logo ...
romfs_load file ecos.bin.lzma.
Decompress kernel ...ok
The total boot time is: 5 s (5628 ms)
cmdline str: mem.
mem_info bank[0]start:90000000, size:1800000.
mem_info bank[1]start:91800000, size:2800000.
The whole mem size: 4000000.
wdt_init, 6605.
-----------[bsp_panel_mod_init] ret = 0----------
-----------[bsp_gpio_mod_init] ret = 0----------
jedec_id=ef4016, ext_id=0
---jedec_id=0xef4016-----
___usbwifi_init____
[cyg_net_init] Init: mbinit(0x0)
[cyg_net_init] Init: cyg_net_init_devs(0x0)
cyg_net_init_devs Init device 'ra0'
___rt_ecos_init____
cyg_net_init_devs Init device empty '0x90634288'
cyg_net_init_devs Init device empty '0x90634298'
[cyg_net_init] Init: loopattach(0x0)
[cyg_net_init] Init: cyg_ppp_pppattach(0x0)
[cyg_net_init] Init: ifinit(0x0)
[cyg_net_init] Init: domaininit(0x0)
[cyg_net_init] Init: cyg_net_add_domain(0x905aab78)
New domain internet at 0x0
sack hole zone : 0x906c2cb0
[cyg_net_init] Init: cyg_net_add_domain(0x905aa828)
New domain route at 0x0
[cyg_net_init] Init: call_route_init(0x0)
[cyg_net_init] Done
USB HCD: device gx-ehci, build at 15:35:26 Sep 19 2018
ehci: 0x908b51ec
ehci->hcs_params=0x2112, num: 2
hcs_params=0x2112
flag=0x0.
hub1=0x2000
hub2=0x2000
ehci base=0xa0900000
operational base= 0xa0900010
gx-ehci gx-ehci.0: gx EHCI
gx-ehci gx-ehci.0: new USB bus registered, assigned bus number 1
ehci_mem_init():ehci->async->qh_dma=0x108c1720
ehci_mem_init():sizeof qtd: 96.
ehci_mem_init():sizeof qh: 128.
gx-ehci gx-ehci.0: supports USB remote wakeup
gx-ehci gx-ehci.0: irq 59, io mem 0xa0900000
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-:1.0 (config #1, interface 0)
hub 1-:1.0: usb_probe_interface
hub 1-:1.0: usb_probe_interface - got id
hub 1-:1.0: USB hub found
hub 1-:1.0: 2 ports detected
hub 1-:1.0: standalone hub
hub 1-:1.0: individual port power switching
hub 1-:1.0: individual port over-current protection
hub 1-:1.0: Single TT
hub 1-:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-:1.0: power on to power good time: 20ms
hub 1-:1.0: local power source is good
hub 1-:1.0: enabling power on all ports
USB HCD: device gx-ohci, build at 15:35:27 Sep 19 2018
--------ohci base= 0xa0a00000
<7>: starting gx OHCI USB Controller no sem_wait.
<7>: Clock to USB host has been enabled
gx-ohci gx-ohci.0: gx OHCI
gx-ohci gx-ohci.0: new USB bus registered, assigned bus number 2
gx-ohci gx-ohci.0: supports USB remote wakeup
gx-ohci gx-ohci.0: irq 58, io mem 0xa0a00000
и всё, в чем может быть причина его висения?
|