Восстановление оборудования на Natonalchip без интерфейса RS-232

[kreshnot]

пример: лог Strong 8500

1:

BOOT_OK!LDR_OK
LZMA Decompression...ok
MDrv_PM_RtcGetCounter(CurrentCounter=0)


Hello U-Boot


U-Boot 1.1.6 (Jun 27 2012 - 08:51:17)

Board: MSTAR KRNOUS (CPU Speed 552 MHz)
DRAM: 128 X 0 MBytes
U-Boot is running at DRAM 0x87600000
###############BOARD CONFIGURATION#####################
DEFAULT ENBALE L2-Cache
FPU(DISABLE)
ENABLE_DDR3_16BIT_MODE
DDR_FREQUENCY(1600MHz)
###############BOARD CONFIGURATION#####################
Module: USB FAT FLASH SPI OSD ENV=SERIAL
Flash is detected (0x0803, 0x01, 0x02, 0x16)
MDrv_SERFLASH_GetInfo()
u32AccessWidth = 1
u32TotalSize = 8388608
u32SecNum = 128
u32SecSize = 65536
In: serial
Out: serial
Err: serial
MSVC00B000100100208768TH0000000T
Hit any key to stop autoboot: 0
MDrv_IIC_InitPort0: OK
MDrv_PNL_Init u32PnlRiuBaseAddr = BF200000
MDrv_PNL_Init u32PMRiuBaseAddr = BF000000
GE_SetOnePixelMode
driver GE init ok
MDrv_HDMITx_Init
Get IOMAP ID:300 Base:BF000000!
MDrv_HDMITx_SetHDMITxMode: HDMI mode
DAC eTiming =6
HDMITx eTiming =7
MDrv_HDMITx_Exhibit: Create Check Rx timer success!
HDMITx eTiming =7
shift -8 pixels in PAL mode
GOP_GWIN_Set_STRETCHWIN Horizonal Src: 1920 Des 1920
GOP_GWIN_Set_STRETCHWIN Vertical Src: 1080 Des 1080
GWIN width:1920, height:1080
get default logo addr
get correct jpeg pic
FPflag = 1

secure boot flag = 0
[BSTRAP] securechip OTP has been set .
offset 0xE0000, size 0xC
WARNING: it is better to set total length aligned to 65536 !!!
Flash is detected (0x0803, 0x01, 0x02, 0x16)
initialization done!
app len 298058
offset 0xE0000, size 0x2A0000
in=0x80B0001C, in_size=0x298058, out= 0x80000180, alloc_buf = 0x81000000
in=0x80B0001C, in_size=0x298058, out= 0x80000180, alloc_buf = 0x81000000
in_size=2719832 out_size=7711092 unpack_size=0


LZMA Decompression...CRC_result FCC9C8D3 CRC_value FCC9C8D3
CRC check success !!
ok

MDrv_IR_Disable-----
## Starting application at 0x80000224 ...

[users12]

Сообщение от kreshnot

пример: лог Strong 8500
....

kreshnot, полезный ЛОГ ! В PUTTY можно спокойно прекратить работу Загрузчика U-Boot 1.1.6 с клавиатуры, далее командами сделать полный BackUp прошивки на USB-флешку, например backup.bin